Concrete Products

All of our high quality concrete sealers and concrete cleaners are manufactured at an ISO 9001 certified facility. ISO 9001 is an Internationally recognized quality standard which measures the ability of a business to address customer requirements and satisfaction.

Concrete Sealer X-1

Concrete Sealer X-1 is a permanent silicate based deep penetrating sealer which means that it is guaranteed to last for the life of your concrete because it chemically bonds to the concrete to become part of its integral structure. It is highly effective in making concrete physically stronger and denser protecting it against frost and salt while increasing its resistance to stains, acids, alkalis, moisture, mold and mildew. This product will cure damp and wet basements by preventing hydrostatic water from penetrating through the concrete. It will also stop dusting, efflorescence, spalling, pitting, crumbling and prevent mold, mildew and algae growth. The product will seal the concrete to significantly reduce the level of radon gas penetration which is known to cause lung cancer by the EPA.

Concrete Sealer X-1 can be used in all commercial and residential applications to treat damp or wet basements, concrete floors, walls, driveways, garages, warehouses, storage tanks, pipes, blocks, grout, mortar and stucco. It can also be used to extend the life of exterior wood including fences, patios, decks, cedar and wood shingles.

Concrete Sealer X-1 is easy to apply using a brush, medium nap roller or low pressure sprayer at any temperature between 40 and 80°F. The surface to be treated does not need any special treatment but it must be oil and dust free to allow proper penetration of the product. You should check the surface of your concrete before applying this product to make sure it absorbs drops of water within a few seconds, if it beads up then use Eco Concrete Etcher prior to applying this product. It will cover approximately 200 to 400 sq. ft. per gallon depending on the concrete porosity and two coats are recommended. Typically a 5 gallon pail will seal a maximum of 1,000 sq. ft. of poured concrete using the two required applications(2,000 sq. ft. total) but this coverage can be lower depending on the porosity.  

Concrete Sealer X-1 penetrates through the capillaries of the concrete to a maximum depth of up to 4" where it chemically neutralizes damaging chemicals to form a hard insoluble structure based on calcium silicate and calcium hydroxide. Unlike surface coatings this product will not be damaged by efflorescence or be worn down by heavy traffic because it is permanent. 

Concrete Sealer X-1 leaves a natural finish (no sheen) after application, it is UV resistant, non-yellowing, breathable and the surface will not be slippery. This sealer is not a repellant coating so the concrete can be painted after it has been sealed with increased paint adhesion because the sealer neutralizes the alkalis in the concrete preventing saponification of the paint. Adhesives and epoxy coatings can also be applied over the sealed concrete with no adverse effects.

Concrete Sealer X-1 is environmentally friendly, non-toxic and nonflammable because it does not contain chemical solvents or release any VOC or noxious fumes.

After cementitious surfaces have been treated with Concrete Sealer X-1 or Concrete Sealer X-2 they can resist many chemical compounds more effectively including acids, salts, solvents, alcohols and oils as shown in this table.

See our FAQ to find out how Concrete Sealer X-1 Works
See our FAQ to find out how Concrete Sealer X-1 Pricing Compares with competitors

Concrete Sealer X-2

Concrete Sealer X-2 is a higher concentration product than Concrete Sealer X-1. It creates the same chemical reactions within the concrete as Concrete Sealer X-1 and it has the same physical properties, coverage rates and application procedures.

Concrete Sealer X-2 has been specifically designed to seal very porous concrete or cinder blocks. This product is also recommended for poured concrete if the concrete is more than 10 years old or if signs of seepage or damage such as dusting and efflorescence are already evident. It is also recommended that this product is used on outdoor concrete surfaces which may be exposed to severe weather conditions.

Concrete Sealer X-2 leaves a natural finish (no sheen) after application, it is UV resistant, non-yellowing, breathable and the surface will not be slippery. This sealer is not a repellant coating so the concrete can be painted after it has been sealed with increased paint adhesion because the sealer neutralizes the alkalis in the concrete preventing saponification of the paint. Adhesives and epoxy coatings can also be applied over the sealed concrete with no adverse effects.

Concrete Sealer X-2 is easy to apply using a brush, medium nap roller or low pressure sprayer at any temperature between 40 and 80°F. The surface to be treated does not need any special treatment but it must be oil and dust free to allow proper penetration of the product. You should check the surface of your concrete before applying this product to make sure it absorbs drops of water within a few seconds, if it beads up then use Eco Concrete Etcher prior to applying this product. It will cover approximately 200 to 400 sq. ft. per gallon depending on the concrete porosity and two coats are recommended. Typically a 5 gallon pail will seal a maximum of 1,000 sq. ft. of poured concrete using the two required applications(2,000 sq. ft. total) but this coverage can be lower depending on the porosity.

Concrete Sealer X-2 is environmentally friendly, non-toxic and nonflammable because it does not contain chemical solvents or release any VOC or noxious fumes.

Concrete Sealer X-2 is a ready to use, DIY type product which has a shelf life of at least two years.

After cementitious surfaces have been treated with Concrete Sealer X-1 or Concrete Sealer X-2 they can resist many chemical compounds more effectively including acids, salts, solvents, alcohols and oils as shown in this table.

See our FAQ to find out how Concrete Sealer X-2 Works
See our FAQ to find out how Concrete Sealer X-2 Pricing Compares with competitors
This product is also guaranteed to last for the life of your concrete.

Concrete Sealer X-3

Concrete Sealer X-3 is a special blend of polysiloxanes which cross link below the surface of the concrete making the concrete surface water repellant and stain resistant allowing spills to be removed more easily. This product can either be applied alone or on top of the X-1 or X-2 products to provide double protection of the concrete with both deep sealing and a repellant finish.

Concrete Sealer X-3 can be applied on all types of decorative and stained pavers, aggregate driveways and walkways, bricks, clay tiles, sandstone, limestone, marble, granite, slate and any natural stones. It can be used on above grade plaster and stucco providing a breathable barrier against water, stains and acids and will seal hair line cracks. The product can also be used to seal swimming pools and fish ponds to prevent water escaping through the concretes' capillaries and pores. It can also be used in dog kennels and agricultural institutions to provide stain resistance which assists in the maintenance of these enclosures.

Concrete Sealer X-3 is easy to apply using a brush, medium nap roller or low pressure sprayer at any temperature between 40 and 80°F. The surface to be treated does not need any special treatment but it must be oil and dust free to allow proper penetration of the product. You should check the surface of your concrete before applying this product to make sure it absorbs drops of water within a few seconds, if it beads up then use Eco Concrete Etcher prior to applying this product. It will cover approximately 200 to 400 sq. ft. per gallon depending on the concrete porosity and two coats are recommended. Typically a 5 gallon pail will seal a maximum of 1,000 sq. ft. of poured concrete using the two required applications(2,000 sq. ft. total) but this coverage can be lower depending on the porosity. 

The product leaves a natural finish (no sheen) after application and the surface will not be slippery.

Concrete Sealer X-3 has also been proven as an effective anti-graffitti barrier helping to prevent paints, aerosols and crayons from adhering to the wall and allowing easy removal if they do.

Concrete Sealer X-3 is a ready to use product and does not require the addition of an activator which means that it does not have a limited pot life unlike some competitive products and it has a shelf life of at least 6 months.

STARTER KIT SPECIAL - TREATS APPROX. 150 SQUARE FEET WITH THE RECOMMENDED TWO APPLICATIONS OF EACH PRODUCT!

	1 gallon of Concrete Sealer X-3 & 1 gallon of Concrete Sealer X-1 WAS $108 NOW ONLY $100!	1 gallon of Concrete Sealer X-3 & 1 gallon of Concrete Sealer X-2 WAS $110 NOW ONLY $102!

SMALL KIT SPECIAL- TREATS APPROX. 750 SQUARE FEET WITH THE
RECOMMENDED TWO APPLICATIONS OF EACH PRODUCT!

	5 gallons of Concrete Sealer X-3 & 5 gallons of Concrete Sealer X-1 WAS $328 NOW ONLY $299!	5 gallons of Concrete Sealer X-3 & 5 gallons of Concrete Sealer X-2 WAS $348 NOW ONLY $319!

MEDIUM KIT SPECIAL- TREATS APPROX. 1,500 SQUARE FEET WITH THE RECOMMENDED TWO APPLICATIONS OF EACH PRODUCT!

	10 gallons of Concrete Sealer X-3 & 10 gallons of Concrete Sealer X-1 WAS $656 NOW ONLY $588!	10 gallons of Concrete Sealer X-3 & 10 gallons of Concrete Sealer X-2 WAS $696 NOW ONLY $628!

LARGE KIT SPECIAL- TREATS APPROX. 3,000 SQUARE FEET WITH THE RECOMMENDED TWO APPLICATIONS OF EACH PRODUCT!

	20 gallons of Concrete Sealer X-3 & 20 gallons of Concrete Sealer X-1 WAS $1,312 NOW ONLY $1,166!	20 gallons of Concrete Sealer X-3 & 20 gallons of Concrete Sealer X-2 WAS $1,392 NOW ONLY $1,246!

Concrete Sealer X-4

Concrete Sealer X-5

Concrete Sealer X-5 produces a low gloss or satin finish that enhances and protects the appearance of all types of interior and exterior decorative, stained and stamped concrete pavers, brick, mortar, masonry, concrete structures and aggregate driveways.

Concrete Sealer X-5 is a special non-yellowing, UV resistant acrylic copolymer blend which protects the surface of the concrete making it repellant to water, freezing temperatures, rain, sun, pollution and also stain resistant. This product is a VOC Compliant, low odor water based combination of a sealer plus an enhancer. It can also be used as a cure and seal 24 hours after the concrete is poured as long as the concrete is damp and not wet. 

Concrete Sealer X-5 can be used on all types of concrete to make it dustproof. It is particularly effective on exposed aggregate surfaces to reduce wear and to eliminate the problem of loose pebbles. The coating is also USDA approved for meat and poultry areas.  

Concrete Sealer X-5 is a DIY type product which is easy to apply using a brush, medium nap roller or an airless sprayer at any temperature between 40 and 80°F. The surface to be treated does not need any special treatment but it must be oil, paint, adhesive and dust free to allow proper adhesion of the product. You should check your concrete before applying this product to make sure it absorbs drops of water within a few seconds, if it beads up then use Eco Concrete Etcher prior to applying this product. It will cover approximately 250 to 400 sq. ft. per gallon per application depending on the concretes' porosity and two coats are recommended 4 to 6 hours apart. The product should be applied in two thin coats and not a single thicker coat. Typically a 5 gallon pail will seal a maximum of 1,000 sq. ft. of poured concrete using the two required applications(2,000 sq. ft. total) but this coverage can be lower depending on the porosity and application method.  If you are applying this product to a smooth surface and you want to add slip resistance to the sealer we recommend that you add 1 to 2 packets of Stone Grip to each 5 gallon pail of sealer.

Concrete Sealer X-5 provides a protective coating which enhances the effect of our selection of 15 different easy to use Instant Concrete Dyes that stain and dry on the concrete in only 5 minutes. 

Concrete Sealer X-5 has also been proven as an effective anti-graffiti barrier helping to prevent paints, aerosols and crayons from adhering to the wall and allowing easy removal if they do. 

Concrete Sealer X-5 is a ready to use product and does not require the addition of an activator which means that it does not have a limited pot life unlike some competitive products and it has a shelf life of at least two years.

Stone Grip

Stone Grip is an anti-slip additive that can be stirred into Concrete Sealer X-4 or Concrete Sealer X-5 when they are applied to very smooth surfaces. It can also be added to any type of coating or paint to provide additional slip resistance.

Stone Grip is a micronized polymer which can be suspended in coatings due to its low density without significantly affecting the viscosity of the coating.

Stone Grip is sold in a 16 ounce container and we recommend adding one or two packets to each 5 gallon pail of our Concrete Sealer products depending on your preference. As the concentration of Stone Grip is increased the more slip resistance that is imparted to the surface but it does also slightly reduce the gloss of the coating.

16 ounces of Stone Grip: $18.99 or buy 3 or more packets and the shipping is FREE

Eco Concrete Etcher

Eco Concrete Etcher is a water-based non-hazardous, non-corrosive, biodegradable, odorless, VOC free, non-flammable concrete etching and cleaning solution. This advanced formula incorporates a blend of organic chemicals and surfactants for the most effective concrete etching solution available. It does not contain phosphoric or hydrochloric (muriatic) acids which present health and environmental risks. including toxic fumes and corrosive run-off.

Eco Concrete Etcher is the preferred eco-friendly and user friendly etching alternative for interior or exterior surface preparation. It opens the pores on hard-troweled or non porous surfaces allow better adhesion prior to application of any of our Concrete Sealer products.

Eco Concrete Etcher is also ideal for cleaning, degreasing and acid etching concrete floors, walls, basements, garages, factories, warehouses, driveways, swimming pools, patios, and containment areas prior to coating, staining or sealing. It can be used on concrete, masonry, cinder block, brick, mortar joints and grout to properly prepare substrates for optimum penetration and adhesion of stains, paints, industrial coatings, and sealers. It also removes dirt, clay, mortar deposits, rust and efflorescence and reduces the pH of new concrete which can burn off sealers, paints and stains.

Eco Concrete Etcher is supplied as a ready to use product which covers 250 to 500 sq. ft. per gallon depending on the concretes’ porosity. Apply with a pump up sprayer or watering can and scrub the surface with a stiff brush for 15 minutes without allowing the product to dry out. Rinsing thoroughly with water 2 or 3 times to neutralize the etching action.

Concrete Cleaner #1

Concrete Cleaner #1 is a highly concentrated product which can be used to clean and degrease concrete, masonry, bricks, stone, mortar and stucco. This product will remove most stains including oils, tar, dirt, grime, adhesives, resins, paints and graffiti.

Concrete Cleaner #1 can be used to clean concrete driveways, sidewalks, patios, parking lots, factory and garage floors, basements, walls, storage tanks, pipes, cinder blocks, mortar and stucco.

Concrete Cleaner #1 is diluted 100:1 with water for light duty cleaning, 10:1 for normal cleaning, 5:1 for heavy duty cleaning and can be used straight if necessary when removing excessive amounts of oil, grease and paint. When used straight Concrete Cleaner #1 will clean approximately 100 square feet per gallon. The product can be fed through a pressure washer for easy dilution and application and then rinsed off thoroughly. If stubborn stains persist the product can be poured directly on to the stain and then worked in with a stiff brush for 10 minutes and then rinsed off. Even when used undiluted this product will not cause any damage to the concrete because it is not acidic unlike other cleaners based on muriatic acid which actually dissolve the concrete to remove the stains.

Drum Pumps

High Quality 5 and 55 Gallon Drum Pumps

Shipping

We offer FREE S&H in USA(48) by FEDEX GROUND.
All orders usually ship the next business day and the above map
shows the estimated number of business days before you will receive your order.
Contact us for your tracking numbers

Payment

Click on any button above to pay by using

Credit Card by Phone
Call 423-400-7313 for an operator to pay by

Check
Mail a check with your order to the address on contact page

COD
We can ship COD. FEDEX charges $7 per parcel.

Contact Us
Contact us and ask for billing upon receipt of your goods.

• Visit our FAQ page for more information.
• Find out about our natural stone products.
• Find out about our services.
• Contact us with any questions you may have.

This Product is Proudly made in the USA. Our Products are not sold through retail stores and are only available exclusively from us shipped direct to you!!

This is Our ARRA Certificate of Conformance
We support the American Recovery and Reinvestment Act (ARRA) of 2009